Fifield Fab Custom Car Audio - iPad MINI KITS
Fifield Fabrications - YOUR BEST SOURCE FOR ALL YOUR CUSTOM TABLET NEEDS!!!!
MINI-SDU
This is our most popular kit and the one we use for all our dash builds! MINI-SDU is a full face Slidedock Universal kit. This kit is designed to "Drop in" and "lift out" of the kit. When the tablet slides away from the dock connector, there is a 3/8" gap to allow for grabbing and removing iPad. There are 1/8" overhanging edges on the the dock connector side and top edge of the iPad which allows the iPad to be mounted vertically without a problem. The top plate has nice beveled edges inside. The back plate is solid and flat and can be cut to allow for access to other items. See our CUSTOM CUT OUT MOD for pre-cut openings for single and double din ISO openings and other features. Dock connector cable is required to be glassed in to secure iPad under retaining lips. Dimensions are 5 13/16" X 8 3/4" once the flange edge is removed. With the flange is 6 9/16" X 9 7/16" $79.95
Price: $79.95
Finish Preference:
iPad type:
MINI-SL
Copy attached YouTube link to see a brief video of this product: https://youtu.be/kmKzXszY7EI MINI-SL is a spring loaded mounting kit for the iPad mini. This kit has the same overhanging retainer lip design as our MINI-SDU that hold in the iPad. This kit has a spring loaded back plate. You just drop in the iPad, push it down, and slide it into the dock connector to lock it in under the lips. Dock cable must be glassed in to lock iPad in place. To remove iPad, simply push it away from dock connector and the the iPad pushes out automatically! It also has a nice finished top edge plate like our MINI-SDU as well. Dimensions are 5 13/16" X 8 3/4"without the flange and 6 9/16" X 9 7/16" with the flange. $94.95
Price: $94.95
Finish Preference:
iPad type:
MINI-SDF
This is the Mini-SDF kit. This is a full faced kit where the iPad drops in from the front of the kit. the kit goes in top side first, drops flat and then slides over into the dock connector (lightning cable is not included and must be glassed or epoxied in). Once docked, there are 1/8" retainer lips that overhang the iPad on the dock side and top side to secure it. To release, slide the iPad away from the cable, push in on the top side of the iPad and the back flex plate will allow the iPad to kick up to release easily and grab. The back plate is totally flat to provide a clean smooth look once removed. Dimensions are 8 3/4" x 5 3/4" x 13/16" with the top flange removed and 9 9/16" x 6 9/16" with flange. Retail price is $99.95
Price: $99.95
iPad mini type:
MINI-SLS
Copy attached YouTube link to see a brief video of this product: https://youtu.be/wTWz1lPPR_k MINI-SLS Mounting kt for the iPad mini. This is our most secure kit yet! The iPad drops onto the spring loaded tray towards the dock connector opening. Dock connector is NOT required to hold the iPad into the kit. You push the iPad toward the dock side, which slides the tray with the iPad down into the kit then the spring loaded tray pushes the iPad under the 1/8" retainer lips, locking it into place. To release, slide the iPad back towards the dock and the tray automatically pushes the iPad up and out for removal. The top edge is rounded, textured, and beveled which makes it great for surface mounting applications. It can also be used for custom glassed in applications. when surface mounting, the mounting surface on the dock side can only be 1/8" thick to clear the spring shafts and dock cable. Top flange dimensions are 6 1/2" x 10 5/16". Without flange it is 5 3/4" x 9 3/32" x 13/16" Retail price is $129.95
Price: $129.95
iPad mini type:
RADIO MOUNT WITH CUT OUT
This is a labor upgrade only for adding a 3/4" spacer and a single din cut out to the back of your kit for adding a rear mounted head unit. We build in ISO mounts so your radio can be bolted into the kit. THIS IS MEANT TO BE USED WITH THE MINI-SDU, SDC, OR SD. This is not a product.
Price: $49.00
CUSTOM CUT OUT MOD
This is labor Modification add-on only for our MINI-SDU, MINI-SDC, OR MINI-SD. We can offer a centered single din or double din ISO cut out in the back plate. Please specify single or double din.This is not a product.
Price: $20.00
CUT CHOICE:
Halo-Mini
Halo-Mini is a add on modification to the Mini-SDU and Mini-SL. We incorporate a halo ring into the kit housing and include a LED string of choice that can be epoxied into place on the back after building in your kit. Just needs 12 volt positive and negative.
Price: $59.00
LED Color:
MINI-DISD
Copy attached YouTube link to see a brief video of this product: https://youtu.be/vVywCKaqM0o MINI-DISD "Dissed" kit for the iPad mini. This kit is similar to our MINI-SD kit with a little extra difference. The top plate has a 1/8" overhang around the entire inside perimeter. The inside top of the frame is open to allow the iPad to slide down into it and there is room for the iPad to slide over and dock into the lightning cable. (lightning cable of your choice must be glassed into kit) Once docked, the iPad is completley secured in by the overhanging top lips. You can cut the entire top edge down as low as the connector opening to work with very short dash bezels. Dimensions are 8 13/16" x 5 7/8" without the front flange and 9 3/8" x 6 1/2" with flange. Retail price is $69.95
Price: $69.95
iPad type:
MINI-SDC
Copy attached YouTube link to see a brief video of this product: https://youtu.be/OEYAIgDhtl4 MINI-SDC iPad Mini SlideDock Connector Opening kit. This kit is the same as our MINI-SD kit with the addition of a connector opening. Kit comes as a full bucket made of ABS plastic with 1/8" overhanging edges all around the front. Either a side or top edge can be cut off to create a slide in dock for vertical or horizontal mounting. Solid back plate can be cut out to expose radio or a/c controls. is dock connector opening. Dimensions 6 9/16" X 9 1/8". Can be cut to a minimum of 5 13/16" X 8 3/8". $59.95 Only for GEN 1,2,3
Price: $59.95
Finish Preference:
iPad mini type:
MINI-SD
Copy attached YouTube link to see a brief video of this product: https://youtu.be/OEYAIgDhtl4 MINI-SD iPad Mini SlideDock kit. Kit comes as a full bucket made of ABS plastic with 1/8" overhanging edges all around the front. Either a side or top edge can be cut off to create a slide in dock for vertical or horizontal mounting. Solid back plate can be cut out to expose radio or a/c controls.There is no dock connector opening, Bluetooth audio is recommended. See our MINI-SDC FOR A KIT WITH A CONNECTOR OPENING. Dimensions 6 9/16" X 9 1/8". Can be cut to a minimum of 5 13/16" X 8 3/8". $55.95 Only for GEN 1,2,3
Price: $55.95
Finish Preference:
iPad mini type:
MINI-PSD ( NO LONGER AVAILABLE)
MINI-PSD is a Full faced side slide in dock for iPad mini. Dock pivots in and out to allow for removal and insertion of iPad mini. Dock sleeve is spring loaded and pivots in and out by pushing on the tablet or sleeve back. Kit frame must be glassed into whatever application it is being built for. A dock connector opening is provided. Dimensions are 9 9/16" x 6 7/8" x 2 3/8" $109.95
Price: $109.95
MINI-U ( NO LONGER AVAILABLE )
MINI-U is a Universal mounting system with pivot latching design and insert option technology. Comes with one insert of choice, additional inserts are becoming available soon. Product has solid back for cutting out radio or AC controls or easy screw in mounting. Insert has teeth on either side of the dock connector that lock into mounting bucket. the top of the insert has a metal tab that makes contact with the magnetic pivoting latch to hold the top of the insert. It is recommended to mount the kit at a slight back angle to avoid fighting gravity and relying on the small magnet to hold the weight of the tablet and the insert. All products are patent pending. Dimensions 7 1/2" x 10" with flange, 6 9/16" x 9 1/16" without flange. 5/8" depth latching mechanism is 1 9/16" deep from back. $94.95
Price: $94.95
MINI-M (NO LONGER AVAILABLE, see MINI-SL as another option )
MINI-M Mounting kit with pivot for iPad mini. This kit has a pivoting back plate for removal of iPad mini. A dock connector is required to hold the bottom edge of iPad. There are foam pads on either side of the dock connector opening that push the iPad into the opposing top edge which has a slight reverse ball edge that overhangs the iPad. You remove the iPad by pressing down and toward the dock connector simultaneously to relieve top pressure and remove tablet. If mounted at a back angle, pads are not necessary and pivoting is easier. Designed for custom installation in car or home. PATENT PENDING Dimensions 7 9/16" x 10 3/16" with flange, 6 5/16" x 8 7/8"" without flange. 5/8" depth latching mechanism is 1 9/16" deep from back. $59.95
Price: $69.95
Website Builder provided by  Vistaprint